Generated code for ntfs_3g_probe command.

[libguestfs.git] / guestfish-actions.pod

diff --git a/guestfish-actions.pod b/guestfish-actions.pod
index ee8e824..ee3f641 100644 (file)
--- a/guestfish-actions.pod
+++ b/guestfish-actions.pod
@@ -6,6 +6,11 @@ This function adds a virtual CD-ROM disk image to the guest.
 
 This is equivalent to the qemu parameter C<-cdrom filename>.
 
+Note that this call checks for the existence of C<filename>.  This
+stops you from specifying other types of drive which are supported
+by qemu such as C<nbd:> and C<http:> URLs.  To specify those, use
+the general C<config> call instead.
+
 =head2 add-drive | add
 
  add-drive filename
@@ -23,6 +28,32 @@ image).
 
 This is equivalent to the qemu parameter C<-drive file=filename>.
 
+Note that this call checks for the existence of C<filename>.  This
+stops you from specifying other types of drive which are supported
+by qemu such as C<nbd:> and C<http:> URLs.  To specify those, use
+the general C<config> call instead.
+
+=head2 add-drive-ro | add-ro
+
+ add-drive-ro filename
+
+This adds a drive in snapshot mode, making it effectively
+read-only.
+
+Note that writes to the device are allowed, and will be seen for
+the duration of the guestfs handle, but they are written
+to a temporary file which is discarded as soon as the guestfs
+handle is closed.  We don't currently have any method to enable
+changes to be committed, although qemu can support this.
+
+This is equivalent to the qemu parameter
+C<-drive file=filename,snapshot=on>.
+
+Note that this call checks for the existence of C<filename>.  This
+stops you from specifying other types of drive which are supported
+by qemu such as C<nbd:> and C<http:> URLs.  To specify those, use
+the general C<config> call instead.
+
 =head2 aug-close
 
  aug-close
@@ -484,6 +515,17 @@ Setting C<whattodrop> to 3 should drop everything.
 This automatically calls L<sync(2)> before the operation,
 so that the maximum guest memory is freed.
 
+=head2 e2fsck-f
+
+ e2fsck-f device
+
+This runs C<e2fsck -p -f device>, ie. runs the ext2/ext3
+filesystem checker on C<device>, noninteractively (C<-p>),
+even if the filesystem appears to be clean (C<-f>).
+
+This command is only needed because of C<resize2fs>
+(q.v.).  Normally you should use C<fsck>.
+
 =head2 equal
 
  equal file1 file2
@@ -914,6 +956,22 @@ Some internal mounts are not shown.
 This moves a file from C<src> to C<dest> where C<dest> is
 either a destination filename or destination directory.
 
+=head2 ntfs-3g-probe
+
+ ntfs-3g-probe true|false device
+
+This command runs the L<ntfs-3g.probe(8)> command which probes
+an NTFS C<device> for mountability.  (Not all NTFS volumes can
+be mounted read-write, and some cannot be mounted at all).
+
+C<rw> is a boolean flag.  Set it to true if you want to test
+if the volume can be mounted read-write.  Set it to false if
+you want to test if the volume can be mounted read-only.
+
+The return value is an integer which C<0> if the operation
+would succeed, or some non-zero value documented in the
+L<ntfs-3g.probe(8)> manual page.
+
 =head2 ping-daemon
 
  ping-daemon
@@ -989,6 +1047,12 @@ function which has a more complex interface.
 This resizes an ext2 or ext3 filesystem to match the size of
 the underlying device.
 
+I<Note:> It is sometimes required that you run C<e2fsck-f>
+on the C<device> before calling this command.  For unknown reasons
+C<resize2fs> sometimes gives an error about this and sometimes not.
+In any case, it is always safe to call C<e2fsck-f> before
+calling this function.
+
 =head2 rm
 
  rm path
@@ -1162,6 +1226,12 @@ This displays the partition table on C<device>, in the
 human-readable output of the L<sfdisk(8)> command.  It is
 not intended to be parsed.
 
+=head2 sleep
+
+ sleep secs
+
+Sleep for C<secs> seconds.
+
 =head2 stat
 
  stat path