Therefore C<sshd> must be running on the virtualization host, and must
be accessible to that host. See B<SERVER REQUIREMENTS> section below.
-The C<virt-p2v> script must only be run from the live CD. It isn't
-designed to run outside this environment and could do Bad Things to
-your machine if you try it. The script contains some checks to try to
-stop you from doing this.
+The C<virt-p2v> script must only be run from the live CD environment.
+It isn't designed to run outside this environment and could do Bad
+Things to your machine if you try it. The script contains some checks
+to try to stop you from doing this.
Virt-p2v does not modify the physical machine, its disks,
configuration etc.
+USB key and PXE boot options are also available. See sections
+B<PXE BOOTING> and B<BOOTING FROM A USB KEY>
+below.
+
=head1 STANDARD USAGE
After booting the live CD-R, you are presented with a series of
from the physical machine's root filesystem. You should probably try
this method even though occasionally it does not work.
+=item Ask for fixed IP address and gateway
+
+In this mode the live CD will ask you for a fixed IP address and
+gateway address, and will configure your chosen interface with these.
+
=item Configure from the shell
In this mode you will be dropped into a command shell and you will
where C<AA.BB.CC.DD> is the IP address and C<GG.HH.II.JJ> is the
gateway.
+=item QEMU user network
+
+This option configures the network for use inside a QEMU user network
+(L<http://fabrice.bellard.free.fr/qemu/qemu-doc.html#SEC30>). It
+should only be used by developers.
+
=back
=item Devices
chance that they could coincide, which would leave a guest unable to
access the virtual network.
+=item Compression
+
+Choose whether to enable or disable compression on disk images as they
+are copied across the network.
+
+If enabled, the C<-C> option is passed to L<ssh(1)>. On fast networks
+this can sometimes be slower.
+
+NB: The disk image is still stored uncompressed on the remote host
+however this option is set.
+
=item Verify and proceed
In this step you are asked to verify the settings above. If any are
=item C<network>
-Set this to the choice for network setup. Use either C<Some Auto> or
-C<Some Shell> for auto-configuration or shell (manual) configuration
-respectively.
+Set this to the choice for network setup. Use one of:
+
+=over 4
+
+=item C<Some Auto>
+
+for auto-configuration
+
+=item C<Some Static>
+
+to specify the interface, address, netmask and gateway statically
+
+=item C<Some Shell>
+
+to launch a shell
+
+=item C<Some QEMUUserNet>
+
+to use a QEMU user network (developers only)
+
+=back
+
+=item C<static_network_config>
+
+This setting only applies if C<network> is set to C<Some Static>,
+in which case you should set this to the static network settings,
+a tuple of (interface, address, netmask, gateway, nameserver):
+
+ Some ("eth0", "192.168.2.5", "255.255.255.0", "192.168.2.1", "192.168.2.1")
=item C<hypervisor>
uniqueness so there is a very small chance that they could coincide,
which would leave a guest unable to access the virtual network.
+=item C<compression>
+
+Set this to C<Some false> to disable compression, or C<Some true> to
+enable compression, or C<None> to ask the user.
+
=back
=head2 ISO ATTACHMENTS
./iso-attach virt-p2v-VERSION.iso virt-p2v
-=head1 BOOTING FROM A USB KEY INSTEAD OF A CD
+Note that ISO attachments only work with real (and emulated) CD-Rs,
+not with other methods of booting such as USB keys and PXE.
+
+=head1 PXE BOOTING
-If you wish to boot from a USB keydrive, use the livecd-iso-to-disk
-tool:
+If you wish to boot over the network using PXE, use the
+C<livecd-iso-to-pxeboot> script (part of C<livecd-tools>).
+
+ livecd-iso-to-pxeboot virt-p2v-$VERSION.iso
+
+then copy the generated subdirectory C<tftpboot/> to the
+right place for your PXE configuration.
+
+Pre-built PXE boot images are also available on the website.
+
+General configuration of DHCP, TFTP and PXE for network booting are
+outside the scope of this document.
+
+=head1 BOOTING FROM A USB KEY
+
+If you wish to boot from a USB keydrive, use the C<livecd-iso-to-disk>
+script (part of C<livecd-tools>):
livecd-iso-to-disk virt-p2v-$VERSION.iso /dev/sdX1
You can also supply an C<HDB> parameter to specify a second disk.
+=head1 MAILING LIST
+
+Please direct questions to the et-mgmt-tools mailing list
+L<http://www.redhat.com/mailman/listinfo/et-mgmt-tools>
+<et-mgmt-tools @ redhat . com>
+
=head1 SEE ALSO
L<virsh(1)>,
git.annexia.org / virt-p2v.git / blobdiff