Added regression test for RHBZ503169#c10

[libguestfs.git] / perl / lib / Sys / Guestfs.pm

diff --git a/perl/lib/Sys/Guestfs.pm b/perl/lib/Sys/Guestfs.pm
index e7f8924..445d9b8 100644 (file)
--- a/perl/lib/Sys/Guestfs.pm
+++ b/perl/lib/Sys/Guestfs.pm
@@ -97,6 +97,11 @@ This function adds a virtual CD-ROM disk image to the guest.
 
 This is equivalent to the qemu parameter C<-cdrom filename>.
 
 
 This is equivalent to the qemu parameter C<-cdrom filename>.
 

+Note that this call checks for the existence of C<filename>.  This
+stops you from specifying other types of drive which are supported
+by qemu such as C<nbd:> and C<http:> URLs.  To specify those, use
+the general C<$h-E<gt>config> call instead.
+

 =item $h->add_drive ($filename);
 
 This function adds a virtual machine disk image C<filename> to the
 =item $h->add_drive ($filename);
 
 This function adds a virtual machine disk image C<filename> to the


@@ -112,6 +117,30 @@ image).
 
 This is equivalent to the qemu parameter C<-drive file=filename>.
 
 
 This is equivalent to the qemu parameter C<-drive file=filename>.
 

+Note that this call checks for the existence of C<filename>.  This
+stops you from specifying other types of drive which are supported
+by qemu such as C<nbd:> and C<http:> URLs.  To specify those, use
+the general C<$h-E<gt>config> call instead.
+
+=item $h->add_drive_ro ($filename);
+
+This adds a drive in snapshot mode, making it effectively
+read-only.
+
+Note that writes to the device are allowed, and will be seen for
+the duration of the guestfs handle, but they are written
+to a temporary file which is discarded as soon as the guestfs
+handle is closed.  We don't currently have any method to enable
+changes to be committed, although qemu can support this.
+
+This is equivalent to the qemu parameter
+C<-drive file=filename,snapshot=on>.
+
+Note that this call checks for the existence of C<filename>.  This
+stops you from specifying other types of drive which are supported
+by qemu such as C<nbd:> and C<http:> URLs.  To specify those, use
+the general C<$h-E<gt>config> call instead.
+

 =item $h->aug_close ();
 
 Close the current Augeas handle and free up any resources
 =item $h->aug_close ();
 
 Close the current Augeas handle and free up any resources


@@ -499,6 +528,15 @@ Setting C<whattodrop> to 3 should drop everything.
 This automatically calls L<sync(2)> before the operation,
 so that the maximum guest memory is freed.
 
 This automatically calls L<sync(2)> before the operation,
 so that the maximum guest memory is freed.
 

+=item $h->e2fsck_f ($device);
+
+This runs C<e2fsck -p -f device>, ie. runs the ext2/ext3
+filesystem checker on C<device>, noninteractively (C<-p>),
+even if the filesystem appears to be clean (C<-f>).
+
+This command is only needed because of C<$h-E<gt>resize2fs>
+(q.v.).  Normally you should use C<$h-E<gt>fsck>.
+

 =item $h->end_busy ();
 
 This sets the state to C<READY>, or if in C<CONFIG> then it leaves the
 =item $h->end_busy ();
 
 This sets the state to C<READY>, or if in C<CONFIG> then it leaves the


@@ -910,6 +948,12 @@ function which has a more complex interface.
 This resizes an ext2 or ext3 filesystem to match the size of
 the underlying device.
 
 This resizes an ext2 or ext3 filesystem to match the size of
 the underlying device.
 

+I<Note:> It is sometimes required that you run C<$h-E<gt>e2fsck_f>
+on the C<device> before calling this command.  For unknown reasons
+C<resize2fs> sometimes gives an error about this and sometimes not.
+In any case, it is always safe to call C<$h-E<gt>e2fsck_f> before
+calling this function.
+

 =item $h->rm ($path);
 
 Remove the single file C<path>.
 =item $h->rm ($path);
 
 Remove the single file C<path>.


@@ -1067,6 +1111,10 @@ This displays the partition table on C<device>, in the
 human-readable output of the L<sfdisk(8)> command.  It is
 not intended to be parsed.
 
 human-readable output of the L<sfdisk(8)> command.  It is
 not intended to be parsed.
 

+=item $h->sleep ($secs);
+
+Sleep for C<secs> seconds.
+

 =item %statbuf = $h->stat ($path);
 
 Returns file information for the given C<path>.
 =item %statbuf = $h->stat ($path);
 
 Returns file information for the given C<path>.